PLUMBING FOR BEGINNERS: THE ESSENTIALS FOR INSTALLING A BATHTUB

Plumbing for Beginners: The Essentials for Installing a Bathtub

Plumbing for Beginners: The Essentials for Installing a Bathtub

Blog Article

Schedule Services

How do you really feel in regards to Tools You Need to Install a New Bathtub ?


How to Install a Bathtub Yourself
Mounting a bathtub isn't exactly rocket science, however it does need solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a new one is additionally a reasonably challenging task. If the old tub is readily available, the task can relocate quickly; if you have to open up a wall to remove the old tub as well as place the new tub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. Make certain you have actually certified yourself for the job and fit trying it. Rather than hiring a specialist to take over a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This post will certainly help you install a new bathtub in your bathroom if you have actually already purchased a new bathtub and also do not need to transform the plan of your previous water pipes.
Your tools and product checklist must comprise the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Planning for the Setup


    Firstly, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to avoid stress on the bath tub.
    Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the provided washers.
    Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its final placement.

    Removing Old Taps


    If you require to change old faucets with new ones as a part of your installment, after that the first thing you should do is disconnect the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome as a result of the restricted accessibility that is frequently the situation.
    Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
    Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.

    Setting up the Bath tub


    Utilizing both wood boards under its feet, put the bath tub in the needed placement. The wooden boards are practical in uniformly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny factors.
    The next objective is to guarantee that the bath tub is leveled all round. This can be attained by checking the level and adjusting the feet on the bathtub until the level reviews degree.
    To mount faucets, fit all-time low of the furthest flexible tap adapter to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
    Activate the water system as well as examine all joints and also new pipework for leaks and tighten them if essential. Fill the bath tub and likewise inspect the overflow outlet and the regular electrical outlet for leakages.
    Finally, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling as well as securing around the bathtub should wait until the bath tub has actually been made use of at the very least when as this will certainly settle it right into its last position.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipelines.
    If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, place the faucet in the mounting opening in the bath/basin making sure that the washers are in place between the faucet as well as the sink. Protect the faucet in position with the manufacturer given backnut. As soon as the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Tub


    In the area where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, causing the water to penetrate the wall surface between the bath and the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
    You can select from a variety of coloured sealers to blend in your fixtures and installations. They are sold in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always load the bathtub with water before securing, to enable the activity experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not consider this movement prior to securing.
    Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly readily available on the marketplace. It is recommended to fit the tiles using waterproof or waterproof glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    As an enthusiastic reader about Installing A Bathtub, I was thinking sharing that piece of content was a good thing. Sharing is caring. Who knows, you may very well be doing someone a favor. Thank you for your time. Please check our site back soon.


    Drainage issues? Inform.

    Report this page